22 contura accessories v-series contura ii & iii contura iv contura xii contura x & xi contura connectors contura x boot contura ii, ii & iv actuator removal tool contura accessories to easily integrate contura products into your system, carlingswitch also offers many accessories, including: marking detail rear view 45 b a packard 630 7 amp, packard 58 6 .770[19.56] 1.0-2.0 20-18 .5-.8 2 orien- tation wire range (2)16-14 (2)1.0-2.0 12 3.0 .950[24.13] tang symbol mm (ref) b awg 16-14 20-22 20-18 .35-.5 .5-.8 (2) 16 (2) 1.3 22-18 (2).5-.8 3.0 12 1.0-2.0 .3-.9 b a 18-14 16-14 (2)22-18 16-12 1.3-3 .8-2 .820[20.83] 42100-1 60295-1 02965470 02965469 part no 02965580 company series 02965471 packard 58 series plain brass .820[20.83] amp 250 series fastin-faston packard metri-pack 630 series 12015832 60253-1 marking detail rear view amp, packard 58 59 amp a b 6 7 2 31 packard 630 4 vc2 8 vb1-01 contura x boot 1.466[37.24] marking detail front view 10 vc1 vc2 1 28 amp 6 b a 9 3 vc2 connector housing (for amp terminals only) vrt actuator removal tool (for flush bracket) 1.050[26.67] 1.266[32.16] .757[19.23] .900 [22.86] top hold flush on bracket and push in top insert points under actuator vc1 connector housing packard 630 marking detail front view 2 10 8 17 amp, packard 58 a 1.266[32.16] vc1 4 b 3 06288318 12010601 q.c. selection guide 42100-2 60295-2 12020035 12052222 60253-2 12015869 12052224 12015870 tin plated brass note: consult delphi packard and/or amp on actual part numbers and availability. amp is a registered trademark of amp inc. harrisburg, pa delphi packard is a registered trademark of delphi-packard electrical systems warren, ohio 3.0 12 tang symbol = packard 630 marking detail rear view 5 amp, packard 58 12084590 2.000[50.80] 3.99 [101.35] 1.466[37.24] .920[23.37] .920[23.37] 1.170[29.72] 1.250[31.75] marking detail front view vch connector housing shows orientation of tang in slot
23 v-series contura ii & iii contura iv contura x & xi contura xii contura accessories contura mounting panels contura hole plug vms mounting panel detail view vh2 hole plug (with wing serrations) .960 [24.38] .080 [2.03] .984 [25.00] 1.90 [48.2] 2.02[51.3] 1.90[48.2] +.008[.2] -.000[.0] +.008[+. 20] -.000[-.00] vms mounting panel hole test cut hole in actual material +.008[.2] -.000[.0] +.008[+.20] -.000[-.00] test cut hole in actual material mounting panel opening (2) units 1.030 [26.16] .670 [17.01] 1.034[26.26] vmm mounting panel middle .960 [24.38] 1.240 [31.50] vh1 hole plug (no wing serrations) (with vc1 connector attached) detail view vh1 hole plug (no wing serrations for ease of removal) 1.450[36.83] .830[21.08] test cut hole in actual material plug mounting hole vm6 mounting panel 1.820 [46.23] .430[10.92] .960[24.38] 1.900 [48.26] 2.300[58.42] 1.970[50.03] mounting panel for additional units, add 1.03[26.2] per unit. for more than 2 v-series switches, add middle section. available in panel thicknesses listed below. consult factory. mounting panel thickness .062[1.57] .187[4.75] .093[2.36] .250[6.35] .125[3.17] .375[9.52] vme mounting panel end 1.910[48.51] 2.300[58.42] 3.400 [86.36] vm3 mounting panel vhp mounting panel plug 1.187[30.14] 1.030 [26.16] 1.460 [37.08] 6.490 [164.85] 2.300 [58.42] 1.340 [34.03] vh2 hole plug (with wing serrations) 1.700 [43.18] 2.300 [58.42] 1.900 [48.26]
|
